Before you jack the car up, put it on level ground, make sure that the tyres are at their normal pressures and that the car is at its normal 'kerb weight' without passengers, and with a full fuel tank. Old Iron never dies... Post your own photos in our Members Gallery. More than likely I'll probably leave it alone though. Pull off the overload spring on the leaf spring pack. How many leaf springs can i remover. Gerardo a. k. a. Mad Chemist.
How Many Leaf Springs Can I Remover
ARE YOU GOING TO USE THE TRUCK FOR HAULING KIND OF/SORT OF HEAVY LOADS? This spring originally had 6 leafs, so that left me with 5 which seems fine as far as I can tell. It did make the rear of the truck ride much better. The "proper" way to remove leafs for lowering. Now I really want to know what the difference is between them. I agree, 2 would be too many at once. Most commonly, replacement is considered only when one of the installed leafs breaks, or when the rear end of the truck seems to sag under light - or even non-existent - loads. Or should I just pull the the very bottom one out and leave the other ones in because my brother has a z71 and he pulled the shortest one on the bottom out and he's low but not dragging the ground. Join Date: Dec 2009. With u-bolt flip, bolts should meet the following specifications: (General Spring).
Removing A Leaf From Leaf Springs
A ratchet strap and second person will come in handy here. Check each shackle bolt and nut for tightness, and tighten any that are slack. Im going to replace the shocks in the rear with some Rancho's. Repeat the steps to install the replacement spring on the other tire. If the spring leaves are really caked with dirt and grease, cleaning them is a messy job. I shall remove the bottom leaf's, take them to the welding shop and cut them up. Extended rear shocks - Any leaf spring that lifts the rear end of the Tacoma above stock should be paired with a new set of rear shocks so that the leaf spring travel is not limited by the stock shocks. That softened the ride a bit and was freakin' easy to do. I might have to ajust driveline angles possibly. I used an ultra high density plastic that was specifically designed for use with heavy metal to metal sliding on assembly lines. How many leaf springs can i remote access. In some cases, the lower, shorter leaves of the spring are not held in place by spring clips, but rely instead on the U-bolts to keep them in line with the rest of the spring. Ike has removed some leaves and generally moves his springs 2" rear ward making an 88" to a 90".
How To Remove A Leaf Spring
1Wear safety glasses to protect your eyes. Kind of the poor-man's lowering job. 30 over 318 4bbl with 444 lift cam and A999 auto trans with 9 1/4 with 3. Prolonged use of the car with only the driver on board may cause a slight sag in the springs on that side of the vehicle. Silverado XST videos.
How Many Leaf Springs Can I Remove One
Or remove one leaf and leave the overload, or don't do this at all? Some threads have said remove the 3rd from the top, but it has a clamp attached so I removed the 4th from the top instead. The bolts will be right above the shock absorber bracket, hanging off the axle. Note: General Spring lists these as 98-00, but they fit 98-04.
How Many Leaf Springs Can I Remote Access
A multi-leaf spring has two or more U-shaped clips towards the outer ends. Two jack stands are now supporting one side of the truck. 05-03-2014, 06:44 PM||# 14|. If it lowers the truck a bit as well that would be great too. Cruiser only no heavy hauling at all. Location: SE CA Imperial County. If the pieces seem loose or rattle when you drive the vehicle, readjust the bolts as soon as possible. Feasible to remove some YJ leafs from leaf springs. Repeat steps 4 and 5 until only brake fluid comes out of the bleeder valve (no air). Then pick springs that are rated as close as possible to your vehicles actual weight and is rated for more than your truck's actual weight. Even with all things considered with problems you should have it done in 6 hrs max, 2 if no problemsrigrunner wrote:thanks but i think ill leave it to someone who know what they are doing.
The previous owner of my 71 utiline took two leaves out of the front springs to lower the truck to a more appealing height with no ill effects. 1960 Land Rover Dormobile, owned since 1978. I'm putting my overloads back in and welding my new perches under the axle to eliminate the flip kit. The intervals at which this is done will be given in your car handbook. The hard facts are lowering should NOT be done by lowering the spring rate. The pan already has an indent where at one time the asxle came in contact with the, before lowering, I am going to have to find a rear sump pan. Yea, I have dearched springs as well done by a spring shop, along with hangers & shackles. Removing a leaf from leaf springs. I've seen guys pull leaves out before, just wondering which leaf you remove. Have a second person sit in the driver seat and pump the brake pedal until it is firm - usually a few pumps.