This process will restore the TV to its factory default settings, which may solve any issues you're experiencing. On the other hand, if the TV's red light blinks 4 or 10 times, the problem is most likely with the main logic board or inverter board wires. The LED light on the front of your TV blinks 2 times when You need to contact a technician. If you have tried all the methods in this article but still have no luck, you'd better contact Hisense's service personnel to help you check and fix it. Then the issue with the power board and it needs replacement. If your Hisense TV is blinking 4 times, don't panic! The Hisense TV will blink red or blue light 2-6 times and will not turn on.
Hisense Tv Won't Turn On Red Light Flashes 6 Times X
You won't need to do anything to boost the process while it's doing its job. HINT: If your TV still has audio, and the backlights are working, I recommend replacing the T-Con board first because that is the fix the majority of the time. Some Hisense TVs don't have a vent. If you haven't fixed the problem yet, or if it keeps recurring, perform a factory reset. To resolve this issue, just remove the LED light panel and replace it with a new one. If that doesn't work, proceed to the third and fourth steps. If your TV power light still flashes, you should replace the faulty hardware like the PSB, T-con board, main board, LED strip, etc. Repairing a Hisense TV is not as difficult to do, but it does require some knowledge of how electronics work. After that, press and hold the TV power button for about one minute.
Blown out internal components. Additionally, most of the time, the problem is just the standby issue that you can correct with a simple reset procedure. Note the proper count of the Red Light blinking on your Hisense TV. A steady red light could mean that your Hisense TV is just on standby mode, or that it's plugged in and ready for use. It is much easier to narrow down and repair a problem after you have identified which of them is the core cause.
Hisense Tv Won't Turn On Red Light Flashes 6 Times Faster
When you're finished removing the power cable from your TV, make sure there are no other wires connected. If you are sure you want to perform a reset, please follow the steps below. In addition, the boards are plug and play which means you don't need to solder anything. Press the Home button of the Hisense remote control. When your Hisense Smart TV software becomes out of date, it starts malfunctioning. Denis is an article/blog and content writer with over 3 years of experience in writing on different niches, including product reviews, buyer's guide, health, travel, fitness, technology, tourism. Symptom- red light comes on, flashes 6 times–. You can take help from a technician as it is not recommended to open the TV back panel by yourself. Now check the board and replace it if required. If the problem is a result of technical issues, our techs can assist you to troubleshoot the TV and walk you through the required procedures to resolve it. There are essentially three reasons why your Hisense could be blinking red: - The TV is in standby mode. Your Hisense smart TV won't turn on or even show red light flashes on other occasions. Hisense TV red light blinks 8 times.
Another responsible factor for which your Hisense TV power light blinks 6 times is the faulty motherboard. Disconnect everything from Power Board, except AC input---Next disconnect everything from Main Board, except IR Sensor--Power on TV--. Click on "Device preference" and go to the bottom. The technicians at the TV repair shop will be able to identify and resolve the problem. The system has a shutdown mechanism that is sensitive enough to detect even just one bad LED in the backlight system.
Hisense Tv Won't Turn On Red Light Flashes 6 Times 7
If you are experiencing any problems with opening or closing your device then please contact our technicians for help. If your backlights are working, but you have no image on your screen, that means the issue is either your T-Con board, or the main board. Visit Nearest TV Repair Shop. You should try resetting and factory resetting your TV before trying anything else. Hisense televisions are known for their durability, but when something goes wrong with them you have to be careful. This code can occur when there is a problem with the cable or power supply connected to your TV, for example, or when the TV power board is faulty. Alternatively, you can confirm the defective backlight issue by point a flashlight to the TV screen.
Malfunctioning Main Board. I hope you have followed the troubleshooting steps to fix the issue. If you experience this issue, unplug the TV and plug it back in. By the way, replacing the main board, power board and/or T con board will not fix this issue. The Burnt LED On LED Strip. Check The Board is Damage or Not. To reconnect the network, unplug the power cord from the back of the TV and plug it back in.